SciCan Statim 2000 Manuale dell'Operatore Scaricare il pdf (Pagina 4)

4 5

2.1 - EXTENSION TEST CABLE

(RPI PART #SCT026)

When testing, troubleshooting or repairing the STATIM au-

toclave, install the RPI Extension Test Cable. By attaching

the Extension Test Cable to the cover and main PC board

as instructed below, you will be able to extend the dis-

tance between the autoclave and the cover thus allowing

you to place the cover in a horizontal (not vertical) position

for easier viewing of the LCD display and easier access to

the keypad.

INSTRUCTIONS

STEP #1 - Disconnect the power to the autoclave. Remove

the cover. Disconnect the two cables from the main PC

board - one cable from the LCD display board and the

other from the keypad. Leave the cover in the horizontal

position (see Figure 2.1A).

STEP #2 - Connect the Extension Test Cable mating con-

nector to the LCD display board cable.

STEP #3 - If the OEM keypad is installed, connect the Ex-

tension Test Cable mating connector to the keypad cable

connector (see Figure 2.1B).

If the RPI keypad is installed, connect the Extension Test

Cable mating connector to the RPI keypad cable connec-

tor - making sure that both connectors have the “This Side

Up” label facing in the upward direction (see Figure 2.1C).

(Note: The RPI keypad cable connector does not have an

alignment key, so it is very important to connect as per in-

structions and Figure 2.1C).

STEP #4 - Connect the Extension Test Cable mating con-

nectors to the main PC board - making sure that the

Extension Test Cable connector has the “This Side Up”

label facing in the upward direction (see Figure 2.1A).

(Caution: If the Extension Test Cable is connected incor-

rectly, severe damage may occur to the autoclave.)

THIS

SIDE

THIS

SIDE

THIS

SIDE

THIS

SIDE

THIS

FIGURE 2.1C

FIGURE 2.1B

FIGURE 2.1A

2.2 - START SWITCH

(RPI PART #SCS021)

When testing the pump or decontaminating the steam

generator/boiler, it is suggested by the OEM to activate the

pump by shorting Pins #18 and #16 together. However,

the RPI Start Switch offers an easier and safer method. By

connecting the RPI Start Switch to the main PC board con-

nector (P1), you control the activation of the pump via a

hand-held switch. In addition, the RPI Start Switch has a

“hold feature” (i.e. running lock) for longer test periods.

INSTRUCTIONS

STEP #1 - Connect the RPI Start Switch connector to Pins

#18 and #16 on the “20 Pin Connector” (P1) located on the

main PC board. (See Figure 2.2 and note the following: To

guide the Start Switch connector to Pins #18 and #16,

start at the pin labeled “20”, count down one pin, which

is Pin #18, then count down one more pin, which is Pin

#16. Gently guide the Start Switch connector to both Pins

#18 and #16, leaving all other pins exposed.) (Caution: If

the Start Switch is connected to any other pins except #18

and #16, severe damage may occur to the autoclave.) See

“Device Activation Chart”, page 47.

STEP #2 - Once the Start Switch is connected, the next

step is to connect the Pump Tester Bottle (see 2.3 “Pump

Tester Bottle” Instructions, page 6). When testing the

pump, press and hold the “momentary” button for

approximately 25 seconds. When decontaminating the

steam generator/boiler, (see Caution note below), press

and slide the “momentary” button into the “hold” (i.e. run-

ning lock) position for approximately 3 minutes. (Caution:

When decontaminating the steam generator/boiler, the

reservoir must be full so that the pump does not run dry

during the process thus causing severe damage to the au-

toclave.) See page 39 - Figure 9.2 for complete steam

generator/boiler cleaning procedure.

SIDE

THIS

FIGURE 2.2

TIP - To guide the Start Switch

Connector to Pins #18 and

#16, start at the pin labeled

“20”, count down one pin,

which is Pin #18, then count

down one more pin, which is

Pin #16. Gently guide the Start

Switch Connector to both Pin

#18 and #16, leaving all other

pins exposed.

LCD Display Board

Connector

Keypad Connector

Label

“THIS SIDE UP”

LCD Display

Board Connector

Extension

Test Cable

OEM

Keypad

Cable Connector

(with alignment key)

Press and hold for

Momentary feature

LCD Display

Board Connector

Extension

Test Cable

RPI

Keypad

Cable Connector

(without alignment key)

Start Switch

(RPI Part #SCS021)

Press and slide for the

“Hold” feature (Running Lock)

1 2 3 4 5 6 7 8 9 ... 28 29

Commenti su questo manuale

Nessun commento

SciCan Statim 2000 Manuale dell'Operatore Pagina 4

Commenti su questo manuale